Supportnet Computer
Planet of Tech

Supportnet / Forum / Windows98

Nach Format C wird CD-Rom Laufwerk nicht mehr erkannt





Frage

Habe Format C ausgeführt und danach mit der Startdiskette für Windows 98 die Neuinstallation eingeleitet, und zwar Option Installation mit CD-ROM Unterstützung. Das System verleugnet jedoch die Existenz des CD-ROM Laufwerks und es werden keine Treiber von der Bootdisk aus installiert, anschließend kommt die Meldung Installation aborted. Wie kann das CD-Laufwerk aktiviert werden, damit ich Windows 98 von CD installieren kann?

Antwort 1 von Roxysoft

Moin Norius,

ich gehe davon aus, dass Du über eine bootfähige Windows CD (sprich Original-CD) verfügst.
Stell´ Dein also BIOS so ein, dass das CD-ROM Laufwerk als first boot device arbeitet.
Beim Neustart des Rechners wählst Du nur Setup von CD-ROM starten.
Den Rest des Installationsvorgangs kennst Du, denke ich.

Gruß

Roxysoft

Antwort 2 von Norius

Hallo Roxysoft,

vielen Dank für die schnelle Antwort. Es handelt sich tatsächlich um eine Original-CD. Aber selbst bei der BIOS-Einstellung CD-ROM Laufwerk als first boot device läuft das Laufwerk nicht an. Das Laufwerk an sich ist definitif o.k.

Gruß,
Norius

Antwort 3 von PcDock

Hi Norius ,

1. wie alt ist dein Computer.?

2. ist es auch ein IDE-CD Rom.??

PcDock

Hardware lebt und ist eigenständig

Antwort 4 von Roxysoft

Hi Norius,

sind in Deinem BIOS beide IDE-Controller aktiviert und die Laufwerke richtig gejumpert und richtig angeschlossen?

Gruß

Roxysoft

Antwort 5 von Norius

Hallo Leute

Es ist ein Pentium100Mhz mit ASUS CD-S500A Ultra DMA 2 IDE Laufwerk richtig gejumpert und richtig angeschlossen. Das Motherboard ist ein ASUS P55T2P4.

Gruß,
Norius

Antwort 6 von Roxysoft

Sind beide IDE-Controller im BIOS aktiviert ? Versuch mal die Laufwerke vom BIOS über AUTO DETECT oder IDE-AUTO-DETECT erkennen zu lassen.

Gruß

Roxysoft

Antwort 7 von Norius

Hallo Roxysoft,

wo im BIOS werden denn die IDE-Controller aktiviert?

Gruß, Norius

Antwort 8 von Roxysoft

Hi Norius

für heute verschwinde ich aus dem Netz. Ich bin morgen nach der Arbeit wieder da. Falls Dein CD-ROM bis dahin nicht läuft, suchen wir weiter nach einer Lösung.
Da es in diesem Forum äußerst fähige Leute gibt, würde es mich wundern wenn Dein Laufwerk nicht zum Laufen gebracht werden könnte.

Gruß

Roxysoft

Antwort 9 von Roxysoft

Schau mal unter den Einstellungen für die Perepherie nach, kann von BIOS zu BIOS (und Rechner zu Rechner) verschieden sein.

Gruß und tschüss für heute

Roxysoft

Antwort 10 von norius

Hallo Roxysoft,

bin für heute auch weg. Vielen Dank und bis morgen


Gruß, Norius

Antwort 11 von Roxysoft

Moin Norius,

hast Du schon durchgecheckt ob im BIOS beide IDE-Controller aktiviert sind ?
Laut Internet sollte Dein Rechner mit einem AWARD-BIOS laufen. Schau mal nach, ob Du die Menüpunkte Integrated Peripherals und Onboard IDE (oder so ähnlich) findest.
Es wäre interessant zu wissen, wie Deine Laufwerke angeschlossen sind.
Da Du mindestens einen funktionierenden Rechner zur Verfügung haben musst, solltest Du Dir mal das BIOS-Kompendium (kostenlos) herunter laden. Es hilft Dir, Dein BIOS besser zu verstehen und einzustellen.

http://www.bios-info.de/bios/compend.htm#

Für Dein Board könnten auch diese Links interessant sein:

http://www2.tomshardware.de/praxis/20000714/index.html
http://www.pcwelt.de/forum/archive/index.php/t-35132.htmlhttp://www.hardwarejournal.de/hardware-k6-4.htm


Gruß aus Bremerhaven

Roxysoft

Antwort 12 von Norius

Hallo Roxysoft

AWARD-BIOS stimmt. Die Menüpunkte Integrated Peripherals und Onboard IDE kann ich nicht finden. Die Festplatte und das CD-Laufwerk sind an eine PCI-Karte angeschlossen, diese trägt die Aufschrift IDE1 und IDE2. Ich habe auch schon die Kabel getauscht - hat auch nichts gebracht. Beim Booten kommt die Meldung IDE Busmaster enabled.
Kann es vielleicht sein, daß ich eine spezielle Bootdisk benötige?

Gruß,
Norius

Antwort 13 von Roxysoft

Hi Norius,

wieso hast Du deine Laufwerke an eine PCI-Karte angeschlossen ?
So alt ist Dein Mainboard doch auch wieder nicht. Es müsste eigentlich über eigene IDE-Ports verfügen.
PCI-Karten sind eigentlich nur als Erweiterung der On board Anschlüsse gedacht und benötigen normalerweise eigene Treiber.
Klemm doch einfach um.

Festplatte als Master auf IDE-1 Deines Boards und CD-ROM als Master auf IDE-2. Auf diese Weise bremst Dein CD-ROM Deine Festplatte nicht aus.

Antwort 14 von PcDock

Hi,

oder wenn es so bei behalten willst, dann musst du den OnBoard-Kontroller auf "Disable" stellen.!!!!

Sonst musst dich nicht wundern wenn kein Cd-Rom gefunden wird.!!

PcDock

Hardware lebt und ist eigenständig

Antwort 15 von Roxysoft

@PcDock

Stimmt, hätte ich auch drauf kommen müssen !
Dank Dir.

Gruß

Roxysoft

Antwort 16 von Norius

hi

finde keine Einstellung für den OnBoard-Kontroller im BIOS....

Gruß, Norius

Antwort 17 von Norius

Die Menüpunkte Integrated Peripherals und Onboard IDE sind in meinem BIOS nicht vorhanden

Antwort 18 von PcDock

Hi Norius,

Schau mal hier und es gibt die Einstellung doch,dann sollte das Pro...

PcDock

Hardware lebt und ist eigenständig

Antwort 19 von Roxysoft

Hab mir gerade Dein Handbuch herunter geladen. Ist auf Englisch.

http://dlsvr02.asus.com/pub/ASUS/mb/sock7/430hx/p55t2p4/p55t2p4-311...

Such mal im BIOS nach dem Menüpunkt Chipset Features Setup. Hoch und runter kommst Du mit den Cursor-Tasten (Pfeil-Tasten), Auswahl mit Eingabe-Taster (Enter) - steht auch am unteren Bildrand.
Wenn Du den Eintrag Chipset Features Setup mit Enter ausgewählt hast, findest Du den Eintrag
Onboard PCI IDE enable. Hier hast Du die Möglichkeit den 1., den 2. oder beide IDE-Controller einzuschalten (enable) oder auszuschalten (disable).
Probier´s mal.

Gruß

Roxysoft

Antwort 20 von Norius

Hallo

Onboard PCI IDE disable ist leider auch nicht die Lösung...
Beim Booten kommt noch immer die Meldung IDE Busmaster enabled.
Der PCI Local Bus ist ein Promise Ultra 100.
Kann es vielleicht sein, daß ich eine spezielle Bootdisk benötige?

Gruß,
Norius

Antwort 21 von Roxysoft

Ist Deine PCI-Karte bootfähig ?
Normalerweise wird von den Onboard IDE Ports gebootet. Spezielle Treiber brauchst Du hierfür nicht.

Klemm Deine Laufwerke probehalber - wie in Antwort 13 beschrieben - auf die Onboard Port um, schalte bei Onboard PCI IDE enable beide IDE-Controller ein (enable) und schon sollte Dein Rechner laufen.

Gruß

Roxysoft

Antwort 22 von Norius

Ob die PCI-Karte bootfähig kann ich nicht sagen. Beim Umklemmen laut Antwort13 und Onboard PCI IDE enable lief die Festpatte nicht mehr an...

Vielen Dank für die heutige Unterstützung, kann leider erst morgen weitermachen.

Bis bald
Gruß, Norius

Antwort 23 von Roxysoft

versuch mal, ob Du hier eine passende Bootdisk findest.

http://www.bootdisk.info/modules.php?modid=1

ich bin für heute auch raus.
Mal sehen ob wir morgen weiterkommen.

Gruß

Roxysoft

Antwort 24 von Roxysoft

Hab’ mir von hier das Handbuch (Englisch) zu Deiner Promise IDE-Karte runtergeladen.
http://www.promise.com/support/download/download_eng.asp

Hast Du die Festplatte über das 80-adrige (40-pol.) Kabel angeschlossen ?

Wenn ja, klemm Deine Laufwerke wieder an die PROMISE-Karte, geh´ ins BIOS und starte IDE HDD Auto detection.
Wenn sich ein rotes Fenster öffnet, dann drücke die Taste z für YES (da Du im BIOS mit amerikanischer Tastatur arbeitest sind z und y vertauscht).
Das musst Du insgesamt 4-mal machen.

Danach 1x ESC und dann F10 drücken.
damit speicherst Du die BIOS-Einstellungen und verlässt das BIOS.

Ich hoffe, Deine Englischkenntnisse reichen aus um den Text unten zu verstehen.

Hard Drive Installation

WARNING: If you wish to use your current bootable drive with the
Windows NT4 or 2000 operating system on the Ultra100, do NOT
connect this hard drive to the Ultra100 controller before installing
the NT driver. You MUST install the NT or 2000 driver first (see
page 11) to the boot drive using your existing hard drive controller.


1. Configure the jumpers of the hard drive you´re preparing to connect to the
Ultra100 using the proper "Master," "Slave," or "Cable-Select" settings. You
may need to refer to your hard drive´s manual for more information. The
instructions here assume you will be installing a single drive on to the
Ultra100 card.
2. Install the hard drive in the proper hard drive bay of your system.
3. Attach the Ultra ATA cable to the hard drive and to one of the IDE connector
on the Ultra100 controller card. The colored edge of the cable(s) indicates pin
1 (see Figure 2 below), and the blue cable connector must be attached to the
Ultra100 connector.
4. Proceed to the Installing Drivers section.

NOTE: You must use an 80-wire, 40-pin cable when connecting
an Ultra ATA/100 hard drive to the Ultra100 controller card. The Ultra100 package contains one 80-wire, 40-pin cables.


Windows 98

Installing Drivers During Windows 98 Installation
The following details the installation of the Ultra100 drivers while installing
Windows 98 (with the Ultra100 controller card already in place). If you´re installing
the Ultra100 drivers on a system with Windows 98 already installed, see "Installing Drivers with Existing Windows 98."

1. After installing the Ultra100 controller card and configuring the hard drive(s),
partition and format your hard drive(s), if necessary.
2. Install Windows 98 normally.
3. After installation, go the "Start" menu and choose "Settings."
4. From the "Settings" menu, choose "Control Panel."
5. In the "Control Panel" window, double-click on the "System" icon.
6. In the "System" window, choose the "Device Manager" tab.
7. In the hierarchical display under "Other Devices" is a listing for "PCI Mass
Storage Controller." Choose it and then press the "Properties" button.
8. Choose the "Driver" tab in the "Properties" window, choose "Update Driver,"
and then press "Next."
9. Choose "Search for a better driver than the one your device is using now
(recommended)," then press "Next."
10. Choose "Specify Location," and then type "A:\WIN95-98" in the text box.
11. Insert the "Ultra100 Driver" diskette into the A: drive.
12. Press the "Next" button. A message informing you that Windows has found
"Win95-98 Promise ULTRA100 (tm) IDE Controller" should appear.
13. Press "Next," then "Finish," then "Yes" when asked if you want to restart your
computer. Be sure to remove the diskette from drive A:.

Antwort 25 von Norius

Hallo Roxysoft,

vielen Dank für die umfangreichen Infos - brauche etwas Zeit um mich durchzuarbeiten.

Nochmals Danke und bis bald,
Norius

Antwort 26 von Roxysoft

Ich hoffe, es klappt diesmal.
Viel Glück,

Roxysoft

Ich möchte kostenlos eine Frage an die Mitglieder stellen:


Ähnliche Themen:


Suche in allen vorhandenen Beiträgen: